ABSTRACT
Propeller agitator is a specialized of various types of substances. It consists of three basic components which are the shaft, blade and the vessel.
In the construction, mild steel was chosen due to it’s inherent properties. After the procurement, the following constructional operations were carried out which included marking out, center punching folding, welding, filling operation, assembling, and painting to beautify the equipment and for other purposes.
The shapes and forms are formulated to obtain the following dimensions of the agitator. These are length of handle = 320mm, diameter of gear teeth = 100mm, thickness of shaft = 20mm, thickness of gear = 12mm, size of blade = 50mm x 100mm, blade diameter = 63mm, inside diameter of pump = 12mm, outside diameter of pump = 20mm, shat height = 470mm, vessel diameter = 340mm and height = 560mm
The agitating mixer has high efficiency of comparable to those produced industrially. The estimated rate of rotation is 1720 rpm.
The cost of construction of the agitator is however minimized due to the preferred choice of the raw material and method of fabrication.
TABLE OF CONTENTS
Title page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of contents
CHAPTER ONE
1.0Introduction
1.1The objective of the project
CHAPTER TWO
2.1The theory and concept of agitation
2.2Type of mixers
2.3The impeller mixers for liquids
2.31Paddles
2.32Turbines
2.33Propellers
2.4The particle mixer for free flowing solids
2.5Mixers for heavy paste or cohesive solids
2.6Agitator effectiveness & agitation index
2.7Degree of agitation
2.8Power consumption in agitators
2.9Agitation rate
2.10Materials for the construction of propeller agitator
2.11Equipments for the fabrication of propeller agitator
CHAPTER THREE
3.1Construction and fabrication procedure
3.2Steps of fabrication process
CHAPTER FOUR
4.0Cost analysis
4.1Material cost
4.2Labour cost
CHAPTER FIVE
5.1Discussion
5.2Recommendation
5.3Conclusion
CHAPTER SIX
Nomenclature
References
Disclaimer: Note this academic material is intended as a guide for your academic research work. Do not copy word for word. Note: For Computer or Programming related works, some works might not contain source codes
CITE THIS WORK
(2012, 12). Construction Of Propeller Agitator.. ProjectStoc.com. Retrieved 12, 2012, from https://projectstoc.com/read/483/construction-of-propeller-agitator
"Construction Of Propeller Agitator." ProjectStoc.com. 12 2012. 2012. 12 2012 <https://projectstoc.com/read/483/construction-of-propeller-agitator>.
"Construction Of Propeller Agitator.." ProjectStoc.com. ProjectStoc.com, 12 2012. Web. 12 2012. <https://projectstoc.com/read/483/construction-of-propeller-agitator>.
"Construction Of Propeller Agitator.." ProjectStoc.com. 12, 2012. Accessed 12, 2012. https://projectstoc.com/read/483/construction-of-propeller-agitator.
- Related Works
- Design And Fabrication Of An Electric Stove / Oven
- Design And Implementation Of An Automated Motor Vehicle Driver’s Licensing System. (a Case Study Of Enugu Motor License Office, Enugu State; Abakpa) Nike).
- Fabrication Of A Standard Wheelbarrow
- The Design And Fabrication Of A Corn Selling Machine
- Design And Fabrication Of An Air Driven Engine
- Design And Implementation Of Simple Scientific Calculator.
- An Overview Of Remediation Techniques Of The Environment
- The Design And Cosntruction Of 1000kwa Stabilizer A Project Presented To The Department Of Electrical/electronics Engineering
- Construction Of A Mobile Refrigerator
- Design And Implementation Of Computerized Budget Analysis System (case Study Of Enugu State Ministry Of Finance)