ABSTRACT
The precise content of this project was to construct a model shell and tube heat exchanger.
The material for construction of this project (equipment) and their dimensions are as follows:
1. 500mm length of a tube bundle
2. 20mm diameter of the tube bundle
3. 650mm length of the shell
4. 120mm diameter of the shell
5. 70mm length of the inlet and outlet
6. 20.5mm diameter of the inlet and outlet
7. 160mm diameter of the flanges
8. 8mm diameter of the holes on the flanges.
The construction of this equipment involves a series of processes which includes:
i. Marking out which was done using metre rule, pair of compasses, scribers and punch.
ii. Cutting of the marked materials to shape
iii. Folding to shape where necessary
iv. Rolling and boring holes as appropriate
v. Welding together by electric welding
vi. Filling for good finish
vii. Assembling together of the individual component.
The carefulness with which the marking out, welding and final assemble of the work was done made it possible for us to obtain an equipment suitable for use as a model shell and tube heat exchanger.
It is established that a horizontal heat exchanger with cold water at the shell side and the treated steam at the tube side is adequate for this operation, with the aim of cooling the steam from the distillation column.
The introduction of vapour (or any hot fluid) and removal of condensate (or a cooler fluid) is near perfection (100%) while the equipment being a heat exchanger is used to recover vapourised liquid in its former form (liquid) or removed heat from a very hot processed fluid. Significantly, this equipment is of great need when vapourised liquid must be recovered back as liquid at specified conditions.
TABLE OF CONTENTS
Title page
Letter of Transmittal
Certification/Approval
Dedication
Acknowledgement
Abstract
Table of Contents
Nomenclature
CHAPTER ONE
Introduction
1.1 Background of the Study
1.2 Statement of the Problem
1.3 Purpose/Aims/Objectives of the Study
1.4 Scope and limitation of the study
1.5 Method of Research
1.6 Significance of the study
CHAPTER TWO
Literature Review
CHAPTER THREE
Methodology
CHAPTER FOUR
Results/Analysis
CHAPTER FIVE
5.1 Discussions
5.2 Conclusion
5.3 Recommendation
References
Appendix
Disclaimer: Note this academic material is intended as a guide for your academic research work. Do not copy word for word. Note: For Computer or Programming related works, some works might not contain source codes
CITE THIS WORK
(2014, 11). Construction Of A Model Shell And Tube Heat Exchanger.. ProjectStoc.com. Retrieved 11, 2014, from https://projectstoc.com/read/5202/construction-of-a-model-shell-and-tube-heat-exchanger-6869
"Construction Of A Model Shell And Tube Heat Exchanger." ProjectStoc.com. 11 2014. 2014. 11 2014 <https://projectstoc.com/read/5202/construction-of-a-model-shell-and-tube-heat-exchanger-6869>.
"Construction Of A Model Shell And Tube Heat Exchanger.." ProjectStoc.com. ProjectStoc.com, 11 2014. Web. 11 2014. <https://projectstoc.com/read/5202/construction-of-a-model-shell-and-tube-heat-exchanger-6869>.
"Construction Of A Model Shell And Tube Heat Exchanger.." ProjectStoc.com. 11, 2014. Accessed 11, 2014. https://projectstoc.com/read/5202/construction-of-a-model-shell-and-tube-heat-exchanger-6869.
- Related Works
- Main Features Of Pump And Pumping Systems
- Repair And Rehabilitation Of A Faculty Refrigerator
- Design And Construction Of A Mobile Refrigerator
- Evaluating The Different Methods Of Corrosion Prevention, Control And Monitoring
- Construction Of A Standard Drawing Desk
- Design And Construction Of A Metallic Book Shelf
- Construction Of A Screw Conveyor With A Single Phase Electric Motor
- Students Industrial Work Experience Scheme In Nigeria Railway Corporation Enugu.
- Bench Shaping Machine
- Design And Fabrication Of An Air Driven Engine