ABSRACT
The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component parts of the sets of sieve and their dimensions are as follows:
Height of sieve 5.5cm
Number of sieves 7
Diameter of sieve 13.5cm
Shape of sieve circular
Height of sieve set 44cm
In fabricating this set of sieves, some factors were taken into consideration and they are:
The capacity of the sieve.
The type of mixture that can be filtered in it.
The types of properties and composition of the mixture.
The type of material to be used for fabrication of the sieve and shaker.
The mechanism of the filtration process and also,
The cost, which is the determinant, factor in fabrication of any equipment.
These factors help greatly in the fulfillment of the objective of this project study. And after fabrication the projects were tested and seem to be working very efficiently with a reasonable separation of particle and cut diameter.
Using the above dimensions, the following fabrication procedures were undertaken, layout, cutting, drilling, welding, filling sand papering, washing and painting, drying assembling.
Finally, the set of sieves and shaker were subjected to the process of washing, painting and drying.
TABLE OF CONTENT
Title page
Approval page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
1.0 INTRODUCTION
CHAPTER TWO
2.0 LITRATURE REVIEW
2.1 Model
2.2 Screening
2.3 Types of screens
2.4 Screen surface
2.5 Factors in selecting screen equipment
2.6 Method of feed
CHAPTER THREE
3.0 MATERIAL OF CONSTRUCTION
3.1 Aluminum and aluminum alloy
3.2 Carbon and low alloys steel
3.3 Corrosion
3.4 Contact or galvanic corrosion
CHAPTER FOUR
4.0 FABRICATIONAL PROCEDURE
4.1 Layout
4.2 Cutting
4.3 Drilling
4.4 Welding
4.5 Filling
4.6 Sand papering
4.7 Washing and painting
4.8 Drying
4.9 Assembling
CHAPTER FIVE
5.0 OPERATION AND MANTENANCE
5.1 Function of some parts of the electrically vibrated screen.
CHAPTER SIX
6.0 RECOMMENDATION AND CONCLUSION
6.1 Costing
REFERENCE.
Disclaimer: Note this academic material is intended as a guide for your academic research work. Do not copy word for word. Note: For Computer or Programming related works, some works might not contain source codes
CITE THIS WORK
(2014, 12). The Fabrication For A Set Of Sieves And Saker.. ProjectStoc.com. Retrieved 12, 2014, from https://projectstoc.com/read/5626/the-fabrication-for-a-set-of-sieves-and-saker-5967
"The Fabrication For A Set Of Sieves And Saker." ProjectStoc.com. 12 2014. 2014. 12 2014 <https://projectstoc.com/read/5626/the-fabrication-for-a-set-of-sieves-and-saker-5967>.
"The Fabrication For A Set Of Sieves And Saker.." ProjectStoc.com. ProjectStoc.com, 12 2014. Web. 12 2014. <https://projectstoc.com/read/5626/the-fabrication-for-a-set-of-sieves-and-saker-5967>.
"The Fabrication For A Set Of Sieves And Saker.." ProjectStoc.com. 12, 2014. Accessed 12, 2014. https://projectstoc.com/read/5626/the-fabrication-for-a-set-of-sieves-and-saker-5967.
- Related Works
- Extraction And Formulation Of Perfume From Plant
- Equipment Design Project On Design An Inverter For The Production Of 100000 Metric Tones Per Year Of Ethanol From Sugar Cane
- Production Of Mes By Transesterification Of Castor Oil
- Production Of Black And Brown Polish
- Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited Enugu Depot
- Temperature And Water Requirement For Leaching Of Caustic Alkali From ‘ngu’
- Cryogenic Science And Engineering
- Design Of A Biogas Plant
- Modification Of Surface, Physical And Chemical Properties Of Activated Carbons For Water Purification
- Production Of Wood Adhesive