ABSTRACT
The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component parts of the sets of sieve and their dimensions are as follows:
Height of sieve 5.5cm
Number of sieves 7
Diameter of sieve 13.5cm
Shape of sieve circular
Height of sieve set 44cm
In fabricating this set of sieves, some factors were taken into consideration and they are:
The capacity of the sieve.
The type of mixture that can be filtered in it.
The types of properties and composition of the mixture.
The type of material to be used for fabrication of the sieve and shaker.
The mechanism of the filtration process and also,
The cost, which is the determinant, factor in fabrication of any equipment.
These factors help greatly in the fulfillment of the objective of this project study. And after fabrication the projects were tested and seem to be working very efficiently with a reasonable separation of particle and cut diameter.
Using the above dimensions, the following fabrication procedures were undertaken, layout, cutting, drilling, welding, filling sand papering, washing and painting, drying assembling.
Finally, the set of sieves and shaker were subjected to the process of washing, painting and drying.
TABLE OF CONTENT
Title page
Approval page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
1.0INTRODUCTION
CHAPTER TWO
2.0LITRATURE REVIEW
2.1Model
2.2Screening
2.3Types of screens
2.4Screen surface
2.5Factors in selecting screen equipment
2.6Method of feed
CHAPTER THREE
3.0MATERIAL OF CONSTRUCTION
3.1Aluminum and aluminum alloy
3.2Carbon and low alloys steel
3.3Corrosion
3.4Contact or galvanic corrosion
CHAPTER FOUR
4.0FABRICATIONAL PROCEDURE
4.1Layout
4.2Cutting
4.3Drilling
4.4Welding
4.5Filling
4.6Sand papering
4.7Washing and painting
4.8Drying
4.9Assembling
CHAPTER FIVE
5.0OPERATION AND MANTENANCE
5.1Function of some parts of the electrically vibrated screen.
CHAPTER SIX
6.0RECOMMENDATION AND CONCLUSION
6.1Costing
REFERENCE.
Disclaimer: Note this academic material is intended as a guide for your academic research work. Do not copy word for word. Note: For Computer or Programming related works, some works might not contain source codes
CITE THIS WORK
(2012, 12). The Fabrication For A Set Of Sieves And Saker.. ProjectStoc.com. Retrieved 12, 2012, from https://projectstoc.com/read/489/the-fabrication-for-a-set-of-sieves-and-saker
"The Fabrication For A Set Of Sieves And Saker." ProjectStoc.com. 12 2012. 2012. 12 2012 <https://projectstoc.com/read/489/the-fabrication-for-a-set-of-sieves-and-saker>.
"The Fabrication For A Set Of Sieves And Saker.." ProjectStoc.com. ProjectStoc.com, 12 2012. Web. 12 2012. <https://projectstoc.com/read/489/the-fabrication-for-a-set-of-sieves-and-saker>.
"The Fabrication For A Set Of Sieves And Saker.." ProjectStoc.com. 12, 2012. Accessed 12, 2012. https://projectstoc.com/read/489/the-fabrication-for-a-set-of-sieves-and-saker.
- Related Works
- Design And Fabrication Of A Dust Extractor
- Design Of A Hudraulic Escalator
- Automobile Motor Vehicle Construction
- Construction Of A Screw Conveyor With A Single Phase Electric Motor
- Thermodynamic Principle Of Energy Conversion
- Design And Fabrication Of An Ice Block Making Machine
- Construction Of An Intruder Alarm System
- Fabrication Of The A Metallic Bookshelf
- Design And Fabrication Of An Air Driven Engine
- Design And Construction Of A Metal Detector