Design And Construction Of A Computer Based Control Of Electrical Appliances

ProjectStoc - 65 pages 7278 words 729 views Project Diploma/Degree/Masters Level Electrical Electronics Engineering ₦10000 Naira ($66.67 USD)

This is a Premium work, paid access only

Register/Login to Access Full Work



INTRODUCTION

This project presents the design and construction of a computer based program used to control office appliance. It is based on a Graphic user interface (GUI) programming language (Visual Basic 6.0), Parallel Port Interactive Mode, Opto-Coupler Isolation of the computer from the appliance to prevent damage to the system should a fault develop in the appliance. The implementation was based on the interaction of the computer with electronic appliance via the 25 Pin Centronics Parallel Port Cable.





TABLE OF CONTENT





 





Title Page -      -      -      -      -      -      -      -      -      -      i





Dedication      -      -      -      -      -      -      -      -      -      ii





Acknowledgement  -      -      -      -      -      -      -      -      iii





Abstract  -      -      -      -      -      -      -      -      -      -      iv





List of Figures -      -      -      -      -      -      -      -      -      v





List of Table    -      -      -      -      -      -      -      -      -      vi





Table of Content     -      -      -      -      -      -      -      -      vii





 





CHAPTER ONE





INTRODUCTION





1.2 Objective of the Project -      -      -      -      -      -      1





1.3  Justification of the Project     -      -      -      -      -      2





1.4  The Scope of the Project -      -      -      -      -      -      2





1.5  Project Report Organization   -      -      -      -      -      3





 





CHAPTER TWO





REVIEW OF RELATED LITERATURE





2.3.1 The Hardware -      -      -      -      -      -      -      -      4





2.3.2  The Software       -      -      -      -      -      -      -      -      7





2.3.3  Parallel Port Basics      -      -      -      -      -      -      -      15





2.4 Opto-Electronic Component   -      -      -      -      -      28





2.5  The Relay -      -      -      -      -      -      -      -      -      34





CHAPTER THREE





METHODOLOGY





3.1  Design Approach    -      -      -      -      -      -      -      37





3.2  Software Development   -      -      -      -      -      -      37





3.2.1 Out Putting Data to the Parallel Port    -      -      -      38





3.2.2 Reading Data from the Parallel Port     -      -      -      40





 





CHAPTER FOUR





ANALYSIS AND DESIGN





CHAPTER FIVE





SYSTEM IMPLEMENTATION AND TESTING





5.1  Functional Test       -      -      -      -      -      -      -      -      51





 





CHAPTER SIX





 CONCLUSION AND RECOMMENDATION





5.1  Conclusion      -      -      -      -      -      -    &a

Disclaimer: Note this academic material is intended as a guide for your academic research work. Do not copy word for word. Note: For Computer or Programming related works, some works might not contain source codes
Register/Login to Access Full Work

CITE THIS WORK

(2015, 08). Design And Construction Of A Computer Based Control Of Electrical Appliances.. Afribary.com. Retrieved 08, 2015, from https://afribary.com/read/6310/design-and-construction-of-a-computer-based-control-of-electrical-appliances-8641
"Design And Construction Of A Computer Based Control Of Electrical Appliances." Afribary.com. 08 2015. 2015. 08 2015 <https://afribary.com/read/6310/design-and-construction-of-a-computer-based-control-of-electrical-appliances-8641>.
"Design And Construction Of A Computer Based Control Of Electrical Appliances.." Afribary.com. Afribary.com, 08 2015. Web. 08 2015. <https://afribary.com/read/6310/design-and-construction-of-a-computer-based-control-of-electrical-appliances-8641>.
"Design And Construction Of A Computer Based Control Of Electrical Appliances.." Afribary.com. 08, 2015. Accessed 08, 2015. https://afribary.com/read/6310/design-and-construction-of-a-computer-based-control-of-electrical-appliances-8641.

Connect with Us